Technology
Technology & QualityEvery category is developed and manufactured in-house, forming a closed loop from fundamental components to complete robot integration. With core technology, capacity and quality under our own control, hardware and software are optimized together — delivering accuracy, response and stability at the same time.
One Closed Loop, Fully Under Our Control
Naxin Power develops and manufactures everything from coils to complete robots, with every critical stage under our own control in a closed industrial chain.
Independent & Secure
Technology, capacity and quality stay under our own control, with stable supply and consistent interfaces.
Engineered to Fit
Every part is developed specifically for our modules and robots; hardware and software are optimized together.
Cost Advantage
End-to-end in-house production keeps the cost structure under control while maintaining performance.
Fast Delivery
Own standardized lines handle both low-volume customization and mass production with short response times.

Highly Integrated, Modular Joint Actuators
Built on our own coils and motors, reducers, magnetic encoders and PCBA driver boards, each module integrates the motor, gear train, sensing unit, drive control and brake into one assembly. No complex secondary assembly is required — the module can be mounted directly into a robot.
Four Core Engineering Capabilities
From precision transmission to closed-loop control, every capability serves the demanding accuracy, dynamics and stability requirements of humanoid robots.
Precision Transmission & Low Backlash
Harmonic reduction is built from three core elements — the wave generator, flexspline and circular spline. Combined with precision tooth profiles and high-accuracy machining, it delivers high transmission accuracy, minimal backlash, high torque density, compact dimensions and quiet, fatigue-resistant operation.
- Sizes 08–32 with ratios of 50 / 80 / 100 / 120
- Backlash down to 10 arcsec; design life of 9,000–10,000 hours
- Two-stage precision planetary option with a standard hollow cable bore
Dual Encoders & High-Precision Feedback
Our in-house magnetic encoders use non-contact field sensing and support a dual-encoder architecture on the motor and output sides, capturing rotor angle, position deviation and speed changes in real time.
- Ultra-high resolution and bandwidth with real-time absolute position output
- Power-off position memory; vibration-, heat-, dust- and water-resistant
- Compensates gearbox backlash and elastic deformation for better repeatability
Multi-Protocol Drive & FOC Control
PCBA driver boards integrate an encoder decoder chip, combining motor drive and encoder signal decoding in one board — fewer external components, simpler robot wiring and higher system stability.
- 37 / 50 / 57 / 66 DRV driver board variants
- CAN / CANopen / RS-485 / EtherCAT / CAN FD
- Custom hardware, firmware adaptation and functional revisions
Deep Customization & Configurable Parameters
Every series supports customization by accuracy, dimensions, load, function and application — covering mechanics, electronics, firmware and parameter tuning. Individual parts, module solutions and complete robot development can all be delivered quickly.
- Mechanical: outer diameter, thickness and shaft bore to order
- Electrical: voltage, speed, torque and power configurable
- Interfaces: lead-out style, connector and IP rating selectable
Full-Chain In-House: Five Core Advantages
From coils and reducers to driver boards and encoders, every critical stage is under our own control.
| Capability | Naxin Power · Full-chain in-house |
|---|---|
| Component sourcing | Coils / reducers / PCBA / encoders all made in-house |
| Hardware–software fit | Purpose-built for our modules and robots, co-optimized |
| Accuracy & response | Dual-encoder loop corrects backlash and elastic deflection |
| Cost & lead time | Own production lines, delivery schedule under our control |
| Customization & service | One-stop mechanical / electronic / firmware customization and support |
Rigorous, Traceable Quality Control
A process-wide QC system covering incoming materials, machining, semi-finished goods, finished products and final inspection. Every product undergoes thermal, vibration, accuracy calibration and extended burn-in testing.
Selection Guidance
Matching models and ratios to load, envelope, accuracy and protocol.
Solution Adaptation
Mechanical, electronic, firmware and parameter tuning for a precise fit.
Commissioning
Host PC tuning tools with on-site or remote integration support.
After-Sales Support
A dedicated technical team providing one-stop service through project launch.
Want to Learn More About Our Technology and Validation?
Download the full selection manual or speak directly with our engineering team.
